Magnets
What you need:
- clear glass pebbles
- mod podge
- scrapbook paper
- foam brush
- scissors
- pencil
- magnets
- hot glue gun
Directions:
Trace the glass pebbles (I found them at a dollar store) onto the back of scrapbook paper of your choice, and cut it out (it doesn't hurt to cut it a little smaller than the pebbles).
Brush some mod podge onto the flat side of the pebble, and place the paper circle on top (pretty side down). Brush some more mod podge on top, and allow to dry.
When it has dried, hot glue your magnets onto the back of the paper (test it on the fridge to make sure you're gluing the right side down). You did it!
Variations:
I tried doing one with just white paper and I wrote a message on it with ball-point pen, which looked neat because it magnified a little. You could also use newsprint, pictures, or whatever patterned paper you would like, the options are endless! :)
 |
| Pinterest vs Reality (mine on bottom) |
Coasters
What you need:
- small square white bathroom tiles
- mod podge
- scrapbook paper
- foam brush
- scissors
- pencil
- felt
- hot glue or tacky glue
- clear acrylic spray (optional)
- ribbon (optional)
Directions:
I bought the tiles from Home Depot in the bathroom tile section. I can't remember how much they cost, but it was inexpensive, probably around 30c each. Trace or measure the scrapbook paper so that it is the same size as the tiles, and cut it out.
Brush mod podge onto the top (smooth edge) of the tiles.
Place the scrapbook paper on top and press it down. Brush more mod podge on top of the paper, and make sure the edges stick. Even though it dries clear, You can still see the streaks, so I brushed across it in straight lines so it looked better. Let it dry (takes a while!)
When it is dry, spray clear acrylic spray on top to seal. (This is optional, I have seen it done by spraying the top instead of the top coat of mod podge. I did both, but one or the other would be fine). Cut out the felt the same size as the tiles.
Use hot glue or tacky glue to stick the felt onto the bottom of the tiles. Let it dry.
To package them, I made sets of 4 that matched/co-ordinated, stacked them on top of each other, and tied them up with a pretty ribbon. I gave a set to my mother-in-law-to-be, and she still hasn't unwrapped it because she thinks it looks so nice with the bow!
This craft makes a great gift (watch out wedding showers), and is fairly inexpensive to make. The only catch is that it takes a while because you have to let everything dry. I made 30 coasters/magnets, and it took me a good evening. I would recommend making a bunch at a time while you have all the stuff out.
Variations:
I have seen this craft done on Pinterest using photos- it would definitely work if you printed them onto normal printer paper/cardstock, but I don't know how well it would work with photo paper. You could also cut out shapes and layer them onto the tile with mod podge in between as well, or like the magnets, write a special message/drawing onto normal paper as a special keepsake.
 |
| Pinterest vs Reality (Mine on bottom) |
I really love your tutorial! It's simple with a lot of pictures! I linked to it from my blog for my crafting party, so people could have a good reference.
ReplyDeleteI have used photos (on photo paper) and it worked great! Love making the coasters!
ReplyDeleteWhat part do you cut the paper to, the top or bottom of tile? And what do you do if there is excess paper hanging off the tile
ReplyDeleteI did it so that it was the same size as the top of the tile. If there is excess paper you can trim it, but this becomes more difficult once the mod podge has set because the paper gets stiff
DeleteI bought a craft board and exacto knife at michaels and cut the paper to 4"x4". No need for trimming if your tiles are 4.25"x4.25".
Deletewhat can you use to make little "feet" on them?
ReplyDeleteI would think the little self stick felt circles would work or it you want to raise it a little higher, you could use small clear glass beads (like the kind used in the magnet tutorial only smaller ones)
DeleteIs this waterproof?
ReplyDeleteNot with the felt. If you use glass beads for feet, i would mod podge the bottom and all sides of the tiles as well to make ik waterproof. Still wouldnt put it in the dish-washing machine
DeleteI used little felt pads I bought in Home Depot. They are already sticky but I also secured them with glue to be safe.
ReplyDeleteI also used clear engine enamel paint to seal the coasters and let them cure for a month. Better option for hot cups.
ReplyDeleteI would love to know how these have held up after a few years of use and abuse. I made the Sharpie tile coasters that you bake a few years back, but after about a year the Sharpie started to come off some. How do these hold up?
ReplyDeleteI would love to know how these have held up after a few years of use and abuse. I made the Sharpie tile coasters that you bake a few years back, but after about a year the Sharpie started to come off some. How do these hold up?
ReplyDeletei would put a layer of modpodge on top of the sharpie, to be sure :)
DeleteCan you do this with fabric instead of paper? I'm a quilter and these would make wonderful quilter friend gifts.
ReplyDeleteYes it would!
DeleteThat is what I was thinking.
DeleteLove this :D Thanks for modpogde ideas
ReplyDeleteI do tiles. I apply primer let dry than modge it let dry than put napkin on it applying hot iron on the napkin, no steam, put parchement paper on top of napkin before ironing, wrinkle free.
ReplyDeleteWhere my problem seems to be it once its dry I varnish it and it often bubbles, its weird. Even with a spray varnish. What could be the issue? Humidity?
Thank you so much this is what im woeking on now you get right to the point ty
ReplyDeleteI used adhesive backed cork for my backing
ReplyDelete